Loading...
Loading...
These guides will take you step-by-step through the safe removal of the Customer Replaceable Unit (CRU) parts of a OptiPlex 5060 Micro Form Factor system. (CRUs are the parts of the system that should not need an engineer to remove or replace.) The guides include pictures referencing what is involved. Table of Contents: CRU Removal Guide Removal Instructions Removal Guide If these guides do not cover what you are looking to do, then you will want to reference your System Manual . The article below provides information about safe practices to consider before working with electrical equipment. Safety precautions when working with electrical equipment Back to Top
N/A
Removal Instructions Note : Click the title of the section you want to open below, in order to see the contents. Show all | Hide all Recommended Tools 1 Small Phillip's head screwdriver 2 Plastic Scribe 3 Small Flat head screwdriver Note : Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without specialty tools, that are not available to our onsite engineers. System Cover Removal Pre-Removal Instructions Before removing the System Cover: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the single thumbscrew that secures the cover to the back of the chassis. Pull the cover towards the front of the system until it unclips and then lift it up and away from the chassis. Hard Disk Drive Assembly Removal Pre-Removal Instructions Before removing the Hard Disk Drive (HDD) Assembly: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover Press the blue tabs on either side of the assembly towards each other [1]. Push the assembly towards the back of the system [2] until it unlocks and lift it out of the system. Pull one side of the assembly away from the drive to disengage the securing pins [1] and lift the drive out of the assembly [2]. M.2 PCIe SSD card Removal Pre-Removal Instructions Before removing the M.2 PCIe SSD card: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover and HDD Assembly Remove the single screw which secures the SSD card [1] to the motherboard. Lift the card up and remove the card from the slot [2] on the motherboard. System Fan Removal Pre-Removal Instructions Before removing the System Fan: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover Press the blue tabs on either side of the fan towards each other [1]. Lift the edge in the middle of the system up [2] so you can lift it up. Turn the fan bracket over so you can disconnect the fan cable from the motherboard. Memory Removal Pre-Removal Instructions Before removing the Memory: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover and System Fan Pull the metal clips on either side of the memory module away from the module [1]. When the memory pops up, pull it out of the slot [2]. Note : Repeat Step 2 for any additional Memory DIMMs located in the system. Serial and PS I/O board Removal Pre-Removal Instructions Before removing the Serial and PS I/O Board: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover and HDD Assembly Disconnect the card cable from the motherboard [1] and remove the four (4) screws which secure the board to the chassis {2, 3,]. PUll the card back from the front of the chassis and lift it up and out of the system. Coin Cell Battery Removal Pre-Removal Instructions Before removing the Coin Cell Battery: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover and option card Press down on the release latch until the coin cell pops out [1] and remove the coin cell battery from the system. Internal Speaker Removal Pre-Removal Instructions Before removing the Internal Speakers: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover and System Fan Disconnect the speaker cable from the motherboard [1] and system fan retention clips. Unscrew to two (2) screws that secure the speaker from the system fan assembly [2] and remove the speaker [3]. WLAN card Removal Pre-Removal Instructions Before removing the wireless network card: During installation or removals of any hardware always ensure that all data is backed up properly Disconnect any telephone, network, or USB cables from the computer Disconnect the computer and all attached devices from their electrical outlets Remove the System Cover and HDD Assembly Remove the single screw which secures the plastic tab to the card [1]. Take off the plastic clip [2] and disconnect the antenna cables from the card [3]. Then remove the card from the slot on the motherboard [4]. If you require further assistance, contact technical Support. Contact Us Go back to the OptiPlex 5060 teardown contents page.
Click on a version to see all relevant bugs
Dell Integration
Learn more about where this data comes from
Bug Scrub Advisor
Streamline upgrades with automated vendor bug scrubs
BugZero Enterprise
Wish you caught this bug sooner? Get proactive today.