OPERATIONAL DEFECT DATABASE
...
...
Document VersionRelease DateDetails607/26/2021Added additional impacted processor and impacted platforms505/28/2020Updated Resolution to make clarification of Step 7404/22/2020Updated Step 7 in Resolution310/15/2019Added additional information to advisory208/21/2019Updated Resolution section with additional information111/29/2018Original document releaseHPE ProLiant Gen9 servers may experience an unexpected reset or shutdown event described in the scenarios below:Scenario 1:The server experiences an unexpected reboot or shutdown with no Integrated Management Log entries present to indicate that a failure occurred.Scenario 2:The server experiences an unexpected reboot or shutdown, and an error similar to the following MAY appear during Power-On Self-Test (POST) on the next system boot, and in the Integrated Management Log:Option ROM POST Error: 1719-Slot 0 Drive Array - A controller failure event occurred prior to this power-up. (Previous lock up code = 0x12) Action: Install the latest controller firmware. If the problem persists, replace the controller.The important item to note in the error message above is the lockup code 0x12. Other lockup codes do not apply to this advisory. The slot number in the error message may vary.Scenario 3:The server experiences an unexpected reboot or shutdown, and the Integrated Management Log has an entry similar to the one below:Uncorrectable Machine Check Exception (Board 0, Processor 2, APIC ID 0x00000040, Bank 0x00000004, Status 0xBA000000'73000402, Address 0x00000000'00000000, Misc 0x00000000'00000000)The following items in the UMCE entry above must be matched:-Bank 0x00000004-Status 0xBA000000'73000402'Other Uncorrectable Machine Check Exception entries that occur at the same time MAY be present in the Integrated Management Log.The following error MAY or MAY NOT be present during POST or in the Integrated Management Log:Option ROM POST Error: 1719-Slot 0 Drive Array - A controller failure event occurred prior to this power-up. (Previous lock up code = 0x12) Action: Install the latest controller firmware. If the problem persists, replace the controller.The important item to note in the error message above is the lockup code 0x12. Other lockup codes do not apply to this advisory. The slot number in the error message may vary.
Any of the ProLiant servers listed in the "Products" section and that are configured with either of the following processor models:- E5-2600 v4 Series Intel Processor- E5-4600 v4 Series Intel Processor- E7-4800 v4 Series Intel Processor
Important: Although error messages may be present indicating a Smart Array controller error, the Smart Array controller is not defective.A previous version of this advisory indicated System ROM 2.64 or later has a microcode patch to address this problem. HPE is modifying our guidance to update affected servers to System ROM version 2.74, which includes the Intel microcode to address this issue and should be applied to any servers experiencing this failure. Intel has documented this issue as errata BDF103 in the Intel Xeon E5-2600 v4 Processor Product Family Specification Update Revision 20.0.The System ROM can be downloaded from the HPE Support Center athttps://support.hpe.com/hpesc/public/homeIn the search field, enter the name of the server platform. In the dropdown list of search results, select "Drivers and Software" for the item in the dropdown list that matches the search term. On the Drivers and Software page, use the filter options on the left to more quickly find the desired System ROM component. Entitlement is required to download System ROM updates.Should this problem recur even after system ROM version 2.64 and later is applied, follow the steps below.1. Update System ROM to version 2.74 if this has not already been done.2. Reboot the server.3. During POST, press F9 to boot into the System Utilities menu.4. In the System Utilities menu, navigate to "System Configuration --> BIOS/Platform Configuration (RBSU) --> Advanced Options --> Uncore Frequency Limiting".5. Select "Enabled" and press "Enter".6. Press F10 to save the change, then press "Y" when prompted to accept the change.7.Press the "ESC" key repeatedly to navigate back to the top menu level. There are two options: Exit and Resume System Boot, or "reboot the system." Select "Reboot the System" and exit System Utilities, then press "Enter" when prompted to exit and reboot the server.8. Allow the server to reboot and boot the OS.If further assistance is needed, contact HPE Customer Support and refer to this number:CFI 21295.Click on the following URL to locate the HPE Customer Support phone number in your country:https://h20195.www2.hpe.com/v2/Getdocument.aspx?docname=A00039121ENW.
Operating Systems Affected:Not Applicable
No external links available for this bug
Click on a version to see all relevant bugs
Hewlett Packard Enterprise Integration
Learn more about where this data comes from
Bug Scrub Advisor
Streamline upgrades with automated vendor bug scrubs
BugZero Enterprise
Wish you caught this bug sooner? Get proactive today.
